Quick log pane

Need new test, action, option? Post request here.
Post Reply
thomasschmeidl
Posts: 166
Joined: Sat Apr 15, 2006 2:14 pm
Location: Germany, Bavaria

Quick log pane

Post by thomasschmeidl »

The quick log pane is very useful. As it is updated continously, it is, however, difficult/impossible (dependant on the update rate) to scroll down and check for some older entries.

WISH/PROPOSAL: Stop updating the quick log pane as long as the mouse hovers over the QLP or its scroll bar.

Q: can I set the update rate manuallly??

Regards
Thomas
KS-Soft
Posts: 13012
Joined: Wed Apr 03, 2002 6:00 pm
Location: USA
Contact:

Post by KS-Soft »

Quick Log displays and should display real-time information. If you need to check old records you may use log viewer or Log Analyzer.
can I set the update rate manuallly??
There is no "rate", its real-time information. HostMonitor updates Quick Log after each test execution (depends on test settings).

Regards
Alex
thomasschmeidl
Posts: 166
Joined: Sat Apr 15, 2006 2:14 pm
Location: Germany, Bavaria

Post by thomasschmeidl »

Thanks for your reply Alex,
Quick Log displays and should display real-time information. If you need to check old records you may use log viewer or Log Analyzer.
We have > 100 devices being checked by aprox. 1000 tests. There are 7 tests per second. Quick log shows the last 50 status changes, 25 of which can be displayed directly, for 25 more you have to scroll. It's all recent information (usually only the last few hours) and it is very helpful to analyze more complex system failures (what happened first? which was the cause, which was the effect?).

My Problem is: I cannot scroll to the end of the list, as the display is set to the top 25 with every update (7 times per second = you have to turn the wheel of your mouse very fast). Log analyzer is a bad alternative, as it doesn't show all the tests (resp. their status changes) together.

Can you help me?

Thomas
KS-Soft
Posts: 13012
Joined: Wed Apr 03, 2002 6:00 pm
Location: USA
Contact:

Post by KS-Soft »

My Problem is: I cannot scroll to the end of the list, as the display is set to the top 25 with every update (7 times per second = you have to turn the wheel of your mouse very fast)
Do you use Full or Reply logging mode for all (most) of your tests? Otherwise HostMonitor would update Quick Log when test changes its status.
Probably we can keep selected record on screen when Quick Log pane is focused :roll:

Regards
Alex
thomasschmeidl
Posts: 166
Joined: Sat Apr 15, 2006 2:14 pm
Location: Germany, Bavaria

Post by thomasschmeidl »

Do you use Full or Reply logging mode for all (most) of your tests?
We use Midnight logging. But the QLP persistently jumps to the top 25 even when there are no new records.
Probably we can keep selected record on screen when Quick Log pane is focused
That would be great. :-)

Thanks

Thomas
KS-Soft
Posts: 13012
Joined: Wed Apr 03, 2002 6:00 pm
Location: USA
Contact:

Post by KS-Soft »

We use Midnight logging. But the QLP persistently jumps to the top 25 even when there are no new records
H'm.. you are right.
Ok, fixed. Update available at www.ks-soft.net/download/hm684b.zip
Please install version 6.82 before using this update.
Also, if you are using RMA for Windows, update agents as well (rma.exe included into archive).

Regards
Alex
thomasschmeidl
Posts: 166
Joined: Sat Apr 15, 2006 2:14 pm
Location: Germany, Bavaria

Post by thomasschmeidl »

Already installed - it's much better now. :P

Propably you will update the rcc.exe in one of the next versions, too.

Thanx a lot!

Thomas
KS-Soft
Posts: 13012
Joined: Wed Apr 03, 2002 6:00 pm
Location: USA
Contact:

Post by KS-Soft »

You are welcome :)
RCC 2.07c: www.ks-soft.net/download/rcc207c.zip

Regards
Alex
thomasschmeidl
Posts: 166
Joined: Sat Apr 15, 2006 2:14 pm
Location: Germany, Bavaria

Post by thomasschmeidl »

Thanx again
Post Reply